The first step of glass door installation: after the glass door is completely removed, do not rush to install the glass door. First, make preparations. This is also an indispensable step in the door installation process. Prepare the materials required for the installation of glass door and home decoration hardware accessories. The preparation of the same tools is also indispensable, except for the preparation of materials, In order to protect the glass door, some details need to be handled

一留出玻璃限位槽，二使用手握細砂輪塊對玻璃門四個角位的倒角進行緩慢磨角，三用木楔釘將木底托固定于地面之上，并用膠水將玻璃飾面粘卡在木方上，對玻璃門進行這樣的處理之后，安裝前的準備工作也就做好了，接下來就是進行玻璃門的安裝了。

First, set aside the glass limit groove; second, use the hand-held fine grinding wheel block to grind the corners of the four corners of the glass door slowly; third, fix the wooden bottom support on the ground with wooden wedge nails, and stick the glass finish on the wood with glue. After such treatment, the preparations before installation are completed, and then the installation of the glass door is carried out. Installation effect drawing of glass door in home

玻璃門安裝第二個步驟：當玻璃門安裝的準備工作已完畢之后，接下來就可以進行玻璃門安裝施工了，是將已經處理好的玻璃門安裝于門框頂部的限位槽內，其次是放到底托上，并將整個玻璃門的位置對好安裝，這樣玻璃門安裝到門框上了，到此玻璃門安裝還沒有結束，還要注入玻璃膠進行封口操作以及玻璃板件的對接操作，還有就是玻璃門拉手的安裝，要想安裝好玻璃門，對于這兩個操作是講究方法的，對于注入玻璃膠進行封口操作方法，將玻璃膠裝入玻璃膠注射槍中.

The second step of glass door installation: after the preparation for glass door installation has been completed, the glass door installation construction can be carried out next. First, install the treated glass door in the limit slot at the top of the door frame, then put it on the bottom support, and align the position of the whole glass door for installation, so that the glass door can be installed on the door frame, So far, the installation of glass door is not over yet. It is also necessary to inject glass glue for sealing operation and docking operation of glass plates, as well as the installation of glass door handle. In order to install the glass door well, pay attention to the methods for these two operations. For the sealing operation method of injecting glass glue, put the glass glue into the glass glue injection gun

用玻璃膠槍的后壓桿端頭板，開始實施注射操作，擠出少量的玻璃膠注入需要封口的地方.

Use the end plate of the rear pressure bar of the glass glue gun to start the injection operation, extrude a small amount of glass glue and inject it into the place to be sealed

要保證在注射的過程中對準縫隙的封口，對于玻璃板件的對接操作方法，有的玻璃門的安裝，往往不僅是使用一塊玻璃板來完成的，可能需要多個玻璃板，因此就需要玻璃板間的對接，在對接的時候注意對接的縫隙要保證在2-3mm之間，當兩個玻璃門對接固定后，就可以將玻璃膠注入縫隙中了，當這些都操作好之后，玻璃門也就安裝好了，待玻璃膠干之后，進行清理就可以了。

To ensure that the gap is sealed in the process of injection, for the docking operation method of glass plates, the installation of some glass doors is often completed not only by using one glass plate, but also by using multiple glass plates. Therefore, the docking between glass plates is required. During the docking, pay attention to ensure that the docking gap is between 2-3mm. When the two glass doors are docked and fixed, The glass glue can be injected into the gap. After these operations are completed, the glass door will be installed. After the glass glue is dry, it can be cleaned.

以上就是今天小編給大家提供的精彩內容，更多的精彩內容請點擊進入我們的網站：濟南玻璃門http://www.ttt001.com

The above is the wonderful content provided by Xiaobian today. For more wonderful content, please click to enter our official website: Jinan glass door http://www.ttt001.com